1. AB管材質混合不均勻。

　　1. The material of AB pipe is mixed unevenly.

　　雙組份美縫劑由環氧原料和固化劑組成。如果兩種原料混合不均勻，就會出現未固化的現象。

　　Two component tackifier is composed of epoxy raw material and curing agent. If the two raw materials are mixed unevenly, there will be uncured phenomenon.

　　解決方案:先打一部分接縫劑，如膠水在膠管中充分混合后，再施工。

　　Solution: first, apply a part of joint agent, such as glue fully mixed in the hose, and then construct.

　　2. 在擠出未完全混合的橡膠材料之前，直接上膠。

　　2. Apply the rubber directly before extruding the incompletely mixed rubber material.

　　解決方案:用膠槍打膠，充分混合后放入攪拌軟管，有必要擠出前面20~30cm的美縫劑，這部分的美縫劑不能用，以后可以開始施工。

　　Solution: use glue gun to glue, mix well and put it into mixing hose, it is necessary to extrude 20 ~ 30cm of front seaming agent, this part of seaming agent can not be used, and construction can be started later.

　　3.施工前沒有清理裂縫。

　　3. Cracks were not cleared before construction.

　　施工前的準備工作除了要保證施工間隙的清潔無灰塵和雜物外，還要保證基層表面干燥、無水。

　　The preparation before construction shall not only ensure that the construction gap is clean and free of dust and sundries, but also ensure that the surface of the base course is dry and free of water.

　　解決方案:施工前先用刷子將灰塵雜物清理干凈，清除包石街工廠提供的接縫錐，然后用干凈的干布擦拭基層表面，將殘留的水漬擦干。

　　Solution: before construction, clean up the dust and sundries with a brush, remove the joint cone provided by Baoshi Street factory, and then wipe the surface of the base course with a clean dry cloth to dry the remaining water stains.

　　4. 施工溫度低，施工現場通風不良。

　　4. The construction temperature is low and the ventilation at the construction site is poor.

　　施工時溫度過低，現場通風不暢，會延長美觀縫劑的固化時間

　　If the temperature is too low during construction and the site ventilation is not smooth, the curing time of aesthetic joint agent will be prolonged

　　解決方案:根據不同施工環境，適當預估接縫劑完全固化時間，如果確定不允許，可以直接咨詢廠家。

　　Solution: according to different construction environment, properly estimate the complete curing time of the joint agent. If it is not allowed, you can directly consult the manufacturer.

　　5. 材料本身的原因。

　　5. The reason of the material itself.

　　在非正規廠家購買的固化劑達不到標準的縫紉劑，產品本身就不合格。

　　If the curing agent purchased by an informal manufacturer fails to meet the standard sewing agent, the product itself will be disqualified.

　　以上就是山東美縫劑對影響美縫劑不干的因素的詳細介紹，想要了解更多歡迎訪問官網http://www.agasrural.com

　　The above is a detailed introduction of the factors that affect the non drying of the tackifier in Shandong. To learn more, please visit the official website http://www.jinanjiusun.com